Anti repellent adhesive (agent)

HOME > Adhesive (Agent) > Anti repellent adhesive (agent)

Environment High Performance Nano & Water base DIY Type Anti Water Repellent Adhesive

Ingredients

PTR-261 series release liner is based on different kinds of polyester film top coated with Fluoro silicone release agent, it was especially designed not only to provide stable and consistent ultra light  release force when in contact with silicone pressure sensitive adhesives, but also maintain good subsequent adhesion strength.

Contents Unit Referred datas
Chemical   Nano Hydrophobic materials
Physical status   Liquid @25oC
Appearance   Small milky Transparency
Solid content ¢H 25 ¡Ó 2
Viscosity ( 26oC) cps        15
Diluted solvent   Water
Specific gravity g/cm3 1.05~1.10
Tg Temp. (Tg) oC -
Contacted angle   ¡Ö110o

Operating ( processing )

  1. Clean every part of car before processing.
  2. Choose more soft tissue.
  3. Slightly pour the adhesive into the tissue.
  4. Daub the adhesive on the car by every part.
  5. Use a soft, clean rag to clean the smearing part soon after finishing daubing.
  6. Check everywhere of the car after daubing adhesive and clean or not.
  7. The capacity of a bottle is 25 ml

Effect after daubing the adhesive
  1. Driving the car on the highway without using wiper during cloudburst (heavy raindrops ).
  2. The effect is highly apparent while the wind blowing and raindrops are heavy.
  3. The effect is apparent as well in the night when it is raining.
  4. It can maintain 6 months of effect without garage (or other protective barns ).
  5. The effect persists for 1 year or more if you have garage (or other protective barns ) .
  6. It just need using your wiper every 5~10 minutes when the raindrops are small or tiny.
  7. The effect of anti-repellence is accompanied with the wind blowing speed.
  8. The effect is not so obvious on the car back mirrors since there is very small wind blowing speed.
  9. We have another products available for the back mirrors of car using only , it is spraying type gel .  it can much improve such status.

Below are the structure of our high performance functional PET protective film series :

  1. Anti scratch PET protective film
    • PET protective film ( 38~ 50um )
    • Hard coated ( anti abrasion )
    • Substrate PET film (100um )
    • Adhesive layer ( 20~30um )
    • PET Release film ( 38~ 50um )
  2. Anti glare PET protective film
    • PET protective film ( 50um )
    • Anti glare coated
    • Substrate PET film ( 100um )
    • Adhesive layer ( 20~30um )
    • PET Release film ( 50um )
  3. Anti Smudge PET protective film
    • PET protective film ( 50um )
    • Anti smudge & Hard coated
    • Substrate PET film ( 50 , 100um )
    • Adhesive layer ( 20~30um )
    • PET Release film ( 38~50um )
  4. Anti Fog PET protective film
    • PET protective film ( 50um )
    • Anti fog coated
    • Substrate PET film ( 50, 100um )
    • Adhesive layer ( 20~30um )
    • Release film ( 38~ 50um )
  5. Anti Repellent PET protective film
    • PET protective film ( 50um )
    • Anti repellence & Hard coated
    • Substrate PET film ( 50 , 100um )
    • Adhesive layer ( 20~30um )
    • PET Release film ( 38~50um )
  6. Customers can negotiate with us if customers just need 2 layers only  ( does not need the upper layer of  50 um  PET protective film )  before placing the order.